• Applicable to TL200A/TL200B/TL250A/TL250B mini FPV kit.
• 0.2mm extreme thin steel sheet applied, the motor is with lower heat and better efficiency.
• Heat-sink design on motor top.
• Equipped with multiple assembly hole for different frame kit.

• Applicable battery: 2-3s
• Propeller: [TL300E] 5’’ tri-propeller
• Max Thrust: 460g
• Face resistance: ≤4mΩ
• Stator Diameter: 18mm
• No load current: 0.4A-0.7A
• Stator Thickness: 6.0
• Slot number: 12
• Motor Pole: 14
• RPM: 2280KV±5%
• Motor Diameter:23mm
• Motor Shaft:2mm
• Weight:18g

Specification ：

• MT1806-2280KV silver cap motor/CCW x1
• 5’’ tri-propeller TL300E x1

Los motores Tmotor Navigator son los mejores motores para multicopteros. Su diseño exclusivo y sus rodamientos EZO Japones lo convierten en el motor por excelencia para sistemas de multicopteros profesionales o aficionados que les guste equipar sus multirrotores con componentes de alta calidad.

Las ficha técnica y tabla de empujes con distintas helices y baterias de de los motores T-motor aparece en la parte inferior, en ocasiones hay que esperar unos segundos.

Specifications:
 

Caracteristicas:

ESC Features:

Voltage: 6-16.8V(2-4S LiPo)

Output Current: 20A

BEC: without

450Hz

Output PWM frequency：8-12KHz

Firmware：BLHeli Multi

Weight：4.3g

Size：25*22mm

EMAX Nano Series ESCs are developed for racing multicopters, based on BLHeli firmware and support OneShot125. They are compatible with Skyline32, Naze32, Pixhawk, CC3D and other mainstream Flight Controllers. They use authentic electronic components to ensure high quality and enhance the current endurance ability.

• Support Oneshot125, active braking (damped light), quick throttle response
• Smaller and lighter than most of multirotor ESCs 
• Compatible with Skyline32, Naze32, Pixhawk, CC3D and other mainstream Flight Controllers
• Opto designed , with twisted pair wire for throttle signal line, strong anti-jamming capability
• Support SimonK and BLHeli

Features

• Use authentic electronic components to ensure high quality and enhance the current endurance ability of the ESC. 
• Based on BLHeli firmware, optimized for high performance with great linearity and much quicker throttle response.
• Special designed for multirotors, and compatible with fixed-wing aircrafts and helicopters.
• Multiple protection features including Low-voltage cut-off protection / over-heat protection / throttle signal loss protection.
• Throttle range can be configured and is fully compatible with all receivers, providing smooth, linear and precise throttle response.
• All parameters can be programmed via using a program card or a transmitter, including default settings.

EMAX NANO Series ESC User Manual V13.0

http://www.emaxmodel.com/upload/index.php/s/2OifPvldyARQ25U

DYS released this quick release tool,  it is easy to carry and use when you assemble the prop with nylon nut screw, one side is M8, another side is M10. And the weight is only 7g for this small CNC part.


Specification:
Material: Alumium alloy
Color: Red
For 4mm/5.5mm/8mm/10mm bullet cap
Weight: 8g

Package Included:
1 XQuick-release Wrench Tool
 

DYS  Race Edition Series delivers exactly what quad racing pilots have been looking for from motors in this tough and demanding class.

With imported NMB bearings, N52 magnets, 0.2mm laminations and available in CW and CCW configuration, the Race Edition Series of motors are capable of producing a massive 1kg of thrust! and that's more than enough to transform your quad into a serious racing contender.

This special edition motor has a PCB but has no motor wires connected.  This allows custom fitting to suit your frames configuration and reduce weight.  

Features:
• New design with imported NMB bearing
• N52 magnets and 0.2mm lamination
• Powerful and capable of providing over 1kg of thrust 
• Hollow shaft with screw to fix the shaft
• Nylon Prop Nut

Specs:
KV: 2550Kv
Operating Voltage: 12-16.8V
Maximum Current: 27.8A
Max Power: 411.4W
Max Thrust: 1020g (14.8V  on 6045 Propeller)
Shaft: 3mm
Weight: 31g
Suggested ESC: 20A
Cell Count: 3-4S
Bolt Hole Spacing: 16mm & 19mm
Rotation: CW CCW

Features:
*New design with imported NMB bearing
*N52 magnet and 0.2mm lamination
*Powerful with 1.1kg thrust to work with BN5045 Prop
*Hollow shaft with screw to fix the shaft
*Special design for the FPV racer champions.

Specifications:
KV..............................................................................................................2300
Configu ration....................................................................................NP
Stator Diameter....................................................................................22.0mm
Stator Length..........................................................................................5.0mm
Shaft Diameter.......................................................................................3.0mm
Motor Dimensions(Dia.*Len)...............................................Φ27.7×19.0mm
Weight (g)...................................................................................................30g
No.of Cells(Lipo).....................................................................................3-5S
Max Continuous current(A)............................................................26.8A
Max Continuous Power(W)...........................................................428.8W
Internal resistance..............................................................................0.06?