Description:

The Holybro Kopis X8 Cinelifter 5” comes in both Ducted and Caged version. This 5” compact design can easily lift a cinematic camera like Komodo, Zcam, BMPCC, GH5, etc, stable flight while maintaining great maneuverability. Great for both entry level pilot getting into Cinelifter or professional drone cinematographers looking for a rig for stable cinematic footage in tight spaces.

It uses x8 5” props with excellent flight efficiency in cruising speeds with smooth and predictable characteristics, minimal throttle modulation is needed for altitude control. The ducts can be easily removed and changed to carbon fiber caged with ease, landing gear can be removed, and ultimate customizability. It is perfect for both indoor flying and outdoor cruising.

Feature:

• 5” compact design with injection molded ducts

• Perfect for indoor flying near people and outdoor cursing

• Easily Swappable duct to cage design (purchase separately)

• Ducted design provides smooth flight & excellent flight efficiency

• Caged design provided greater maneuverability, especially in winy situation

ARF Kit Contents:

• Frame Kit

• Motor: T-Motor F60 PRO-IV KV1750 (8pc)

• Propeller: Gemfan Hulkie 5055S-3

• 2x MMCX to SMA Female 20cm Antenna Extension Cable For Air Unit 

Mechanical Specification:

Dimension: 31.5 x 31.5cm

Frame Kit Weight:

• Caged Version: 570g

• Ducted Version: 716g

Download:

• 3D Print File

• Duct CAD File

​​
Assembly Guide:

• Duct Version

• Cage Version

Description:

The Holybro Kopis X8 Cinelifter 5” comes in both Ducted and Caged version. This 5” compact design can easily lift a cinematic camera like Komodo, Zcam, BMPCC, GH5, etc, stable flight while maintaining great maneuverability. Great for both entry level pilot getting into Cinelifter or professional drone cinematographers looking for a rig for stable cinematic footage in tight spaces.

It uses x8 5” props with excellent flight efficiency in cruising speeds with smooth and predictable characteristics, minimal throttle modulation is needed for altitude control. The ducts can be easily removed and changed to carbon fiber caged with ease, landing gear can be removed, and ultimate customizability. It is perfect for both indoor flying and outdoor cruising.

Feature:

• 5” compact design with injection molded ducts

• Perfect for indoor flying near people and outdoor cursing

• Easily Swappable duct to cage design (purchase separately)

• Ducted design provides smooth flight & excellent flight efficiency

• Caged design provided greater maneuverability, especially in winy situation

Full Kit Contents:

• Frame Kit

• Motor: T-Motor F60 PRO-IV KV1750 (8pc)

• Propeller: Gemfan Hulkie 5055S-3

• Flight Controller: Kakute H7

• ESC: 2x Tekko32 F4 4in1 50A ESC

• 2x MMCX to SMA Female 20cm Antenna Extension Cable For Air Unit 

Mechanical Specification:

Dimension: 31.5 x 31.5cm

Frame Kit Weight:

• Caged Version: 570g

• Ducted Version: 716g

Download:

• 3D Print File

• Duct CAD File

​​
Assembly Guide:

• Duct Version

• Cage Version

Features

• Frame:4mm 3k carbon fiber
• Flight Controller: Kakute H7 mini (updated)
• ESC: Tekko32 F4 4in1 mini 45A ESC (updated)
• 5.8G VTx: Atlatl HV Micro
• Motor: F1507 KV3800
• Propeller: T3140
• FPV camera: RunCam Racer Nano 2
• Adjustable camera uptilt from 10 degrees to 90 degrees
• Buzzer included.
• Battery plug: XT30
• Wheelbase: 137mm
• Weight:145g
• Recommend battery: 850mAh 4s

Specifications

Includes:

• 1x Kopis FPV racing drone
• 8x T3140 Propeller
• 1x TPU 3D Print
• 1x Battery strap(installed)

Manual:

 Holybro_Kopis Racing 3" (R-XSR_version)_Manual

3D Print:

Holybro_Kopis Racing 3" 3D Print.rar

The Pixhawk ® 5X by Holybro is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk ® FMUv5X Open Standard and the Pixhawk ® Autopilot Bus Standard. It comes with the latest PX4 Autopilot ® pre-installed, triple redundancy, temperature-controlled, isolated sensor domain, delivering incredible performance and reliability.

Inside the Pixhawk® 5X, you can find an STMicroelectronics ® based STM32F7, paired with sensor technology from Bosch®, InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications. The Pixhawk® 5X’s F7 microcontroller has 2MB flash memory and 512KB RAM. The PX4 Autopilot takes advantage of the increased power and RAM. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models.

The FMUv5X open standard includes high-performance, low-noise IMUs on board, designed for better stabilization. Triple redundant IMU & double redundant barometer on separate buses. When the PX4 Autopilot detects a sensor failure, the system seamlessly switches to another to maintain flight control reliability.

An independent LDO powers every sensor set with independent power control. Newly designed vibration isolation to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances. External sensor bus (SPI5) has two chip select lines and data-ready signals for additional sensors and payload with SPI-interface, and with an integrated Microchip Ethernet PHY (LAN8742AI-CZ-TR), high-speed communication with mission computers via ethernet is now supported. Two smart battery monitoring ports (SMBus), support for INA226 SMBus Power module.

The Pixhawk® 5X is perfect for developers at corporate research labs, startups, academics (research, professors, students), and commercial applications.

Features

• Modular flight controller: separated IMU, FMU, and Base system connected by a 100-pin & a 50-pin Pixhawk® Autopilot Bus connector, designed for flexible and customizable systems
• Redundancy: 3x IMU sensors & 2x Barometer sensors on separate buses, allowing parallel and continuous operation even in the event of a hardware failure
• Triple redundancy domains: Completely isolated sensor domains with separate buses and separate power control
• Newly designed vibration isolation system to filter out high-frequency vibration and reduce noise to ensure accurate readings
• Ethernet interface for high-speed mission computer integration
• Automated sensor calibration eliminating varying signals and temperature
• IMUs are temperature-controlled by onboard heating resistors, allowing the optimum working temperature of IMUs
• Two smart batteries monitoring on SMBus
• Additional GPIO line and 5V for the external NFC reader
• Secure element for secure authentication of the drone (SE050)

Specifications

• FMU Processor: STM32F765
  • 32 Bit Arm® Cortex®-M7, 216MHz, 2MB memory, 512KB RAM
• IO Processor: STM32F100
  • 32 Bit Arm® Cortex®-M3, 24MHz, 8KB SRAM
• On-board sensors
  • Accel/Gyro: ICM-20649
  • Accel/Gyro: ICM-42688P
  • Accel/Gyro: ICM-20602
  • Mag: BMM150
  • Barometer: 2x BMP388

Electrical data

• Voltage Ratings:
  • Max input voltage: 6V
  • USB Power Input: 4.75~5.25V
  • Servo Rail Input: 0~36V

Mechanical data

• Dimensions
  • Flight Controller Module: 38.8 x 31.8 x 14.6mm
  • Standard Baseboard: 52.4 x 103.4 x 16.7mm
• Weight
  • Flight Controller Module: 23g
  • Standard Baseboard: 51g

Interfaces

• 16- PWM servo outputs
• R/C input for Spektrum / DSM
• Dedicated R/C input for PPM and S.Bus input
• Dedicated analog / PWM RSSI input and S.Bus output
• 4 general-purpose serial ports
  • 3 with full flow control
  • 1 with separate 1A current limit
  • 1 with I2C and additional GPIO line for external NFC reader
• 2 GPS ports
  • 1 full GPS plus Safety Switch Port
  • 1 basic GPS port
• 1 I2C port
• 1 Ethernet port
  • Transformerless Applications
  • 100Mbps
• 1 SPI bus
  • 2 chip select lines
  • 2 data-ready lines
  • 1 SPI SYNC line
  • 1 SPI reset line
• 2 CAN Buses for CAN peripheral
  • CAN Bus has individual silent controls or ESC RX-MUX control
• 2 Power input ports with SMBus
• 1 AD & IO port
  • 2 additional analog input
  • 1 PWM/Capture input
  • 2 Dedicated debug and GPIO lines

PX4 Guide

• Product Overview
• Wiring Quick Start Guide

Product Detail

• Pixhawk5X_Dimensions
• Pixhawk5X_Pinout
• Pixhawk5X_Spec_Overview
• PM02D_Power_Module_Manual

Pixhawk5x follows the Pixhawk Standard below 

• DS-011 Pixhawk Autopilot v5X Standard
• DS-010 Pixhawk Autopilot Bus Standard
• DS-009 Pixhawk Connector Standard

Includes

• 1 x Pixhawk 5X Flight Controller Module
• 1 x Pixhawk 5X Standard Baseboard
• 1 x Power Distribution Board
• 1 x PM02D Power Module
• 1 x Cable Set
• 1 x M8N GPS

Overview 

This Holybro SiK Telemetry Radio is a small, light and inexpensive open source radio platform that typically allows ranges of better than 300m “out of the box” (the range can be extended to several kilometres with the use of a patch antenna on the ground).

This radio is plug-n-play all Pixhawk Standard and other Flight Controller, providing the easiest ways to setup a telemetry connection between your Autopilot and a ground station. It uses open source firmware which has been specially designed to work well with MAVLink packets and to be integrated with the Mission Planner, Ardupilot, QGroundControl, PX4 Autopilot.

The radios can be either 915Mhz or 433Mhz and you should purchase the model which is appropriate for your country/region. 

Note:

The current batch of Sik Telemtry Radio uses the SI1060 chip (previously SI1000) shipped with updated firmware. Older firmware without SI1060 chip support is not compatible.
Please use Mission Planner 1.3.76 or QGroundControl v4.2.0 or newer if firmware upload is required.

Features

• Open-source SIK firmware
• Plug-n-play for Pixhawk Standard Flight Controllers
• Easiest way to connect your Autopilot and Ground Station
• Interchangeable air and ground radio
• Micro-USB port (Type-C Adapter Cable Included)
• 6-position JST-GH connector

Specification

• 100 mW maximum output power (adjustable) -117 dBm receive sensitivity
• RP-SMA connector
• 2-way full-duplex communication through adaptive TDM UART interface
• Transparent serial link
• MAVLink protocol framing
• Frequency Hopping Spread Spectrum (FHSS) Configurable duty cycle
• Error correction corrects up to 25% of bit errors Open-source SIK firmware
• Configurable through Mission Planner & APM Planner
• FT230X is a USB to BASIC UART IC

Dimensions

• 28 x 53 x 10.7mm (without antenna)

Electrical Data

• Supply voltage: 5V DC (from USB or JST-GH) 
• Transmit current: 100 mA at 20dBm
• Receive current: 25 mA
• Serial interface: 3.3 V UART

FCC IDENTIFIER: 2AP22-HT03-V3

Package Included

Manual:

High Precision GNSS Antennas

SKU8082  GNSS Antenna-CH3602A (Applicable for H-RTK M8P Helical)

KEY FEATURES:

• Support GPS, Glonass, Galileo, Beidou,QZSS, and SBAS signal reception
• Stable phase center guarantees the accuracy of positioning within millimeter level
• Strong anti-interference ability to endure the harsh operating environments
• 25g light weight for lower power consumption
• IP67 ruggedized protection

SKU8086  GNSS Antenna-CH7604A  (Applicable for H-RTK F9P Helical)

KEY FEATURES:

• Support GPS, Glonass, Galileo, Beidou,QZSS, and SBAS signal reception
• Stable phase center guarantees the accuracy of positioning within millimeter level
• D-QHA technology ensures multi-system satellite tracking
• 25g weight, low power consumption ,55 mA@3.3VDC only
• IP67 ruggedized protection

Dimensions

CH3602A&CH7604A GNSS Antennas

CS7624A GNSS Antennas​​​​​​

 

Download

GNSS Antenna CH3602A_Spec
GNSS Antenna H7604A_Spec
GNSS Antenna CS7624A_Spec

High Precision GNSS Antennas

SKU8082  GNSS Antenna-CH3602A (Applicable for H-RTK M8P Helical)

KEY FEATURES:

• Support GPS, Glonass, Galileo, Beidou,QZSS, and SBAS signal reception
• Stable phase center guarantees the accuracy of positioning within millimeter level
• Strong anti-interference ability to endure the harsh operating environments
• 25g light weight for lower power consumption
• IP67 ruggedized protection

SKU8086  GNSS Antenna-CH7604A  (Applicable for H-RTK F9P Helical)

KEY FEATURES:

• Support GPS, Glonass, Galileo, Beidou,QZSS, and SBAS signal reception
• Stable phase center guarantees the accuracy of positioning within millimeter level
• D-QHA technology ensures multi-system satellite tracking
• 25g weight, low power consumption ,55 mA@3.3VDC only
• IP67 ruggedized protection

SKU8106  GNSS Antenna-CS7624A  (Applicable for H-RTK M8P Base & H-RTK F9P Base)

KEY FEATURES

• Support GPS, Glonass, Galileo, Beidou, QZSS and SBAS signal reception
• Stable phase center guarantees the accuracy of positioning within millimeter-level
• Strong anti-interference ability to endure the harshest operating environments
• IP67 ruggedized protection
• Connector :TNC female
• Mounting : BSW5/8''-11 screw,Depth:12-14mm
• Weight :440g 

Package Includes:

- High Precision GNSS Antenna(CS7624A) *1
- Male-male SMA-TNC cable(length: 5m) *1
- 1/4'' Female to 5/8'' -11 Male Adapter *1

Dimensions

CH3602A&CH7604A GNSS Antennas

CS7624A GNSS Antennas​​​​​​

Download

GNSS Antenna CH3602A_Spec
GNSS Antenna H7604A_Spec
GNSS Antenna CS7624A_Spec

High Precision GNSS Antennas

SKU8082  GNSS Antenna-CH3602A (Applicable for H-RTK M8P Helical)

KEY FEATURES:

• Support GPS, Glonass, Galileo, Beidou,QZSS, and SBAS signal reception
• Stable phase center guarantees the accuracy of positioning within millimeter level
• Strong anti-interference ability to endure the harsh operating environments
• 25g light weight for lower power consumption
• IP67 ruggedized protection

SKU8086  GNSS Antenna-CH7604A  (Applicable for H-RTK F9P Helical)

KEY FEATURES:

• Support GPS, Glonass, Galileo, Beidou,QZSS, and SBAS signal reception
• Stable phase center guarantees the accuracy of positioning within millimeter level
• D-QHA technology ensures multi-system satellite tracking
• 25g weight, low power consumption ,55 mA@3.3VDC only
• IP67 ruggedized protection

SKU8106  GNSS Antenna-CS7624A  (Applicable for H-RTK M8P Base & H-RTK F9P Base)

KEY FEATURES

• Support GPS, Glonass, Galileo, Beidou, QZSS and SBAS signal reception
• Stable phase center guarantees the accuracy of positioning within millimeter-level
• Strong anti-interference ability to endure the harshest operating environments
• IP67 ruggedized protection
• Connector :TNC female
• Mounting : BSW5/8''-11 screw,Depth:12-14mm
• Weight :440g 

Package Includes:

- High Precision GNSS Antenna(CS7624A) *1
- Male-male SMA-TNC cable(length: 5m) *1
- 1/4'' Female to 5/8'' -11 Male Adapter *1

Dimensions

CH3602A&CH7604A GNSS Antennas

CS7624A GNSS Antennas​​​​​​

Download

GNSS Antenna CH3602A_Spec
GNSS Antenna H7604A_Spec
GNSS Antenna CS7624A_Spec

SKU31052  Mini Tripod mount
Material: aluminum ( CNC manufacturing) 
Mounting screw: 1/4 inch thread &  1/4''Female to 5/8''-11 Male Adapter
Applicable for H-RTK M8P Base SKU12021 &  H-RTK F9P Base SKU12022 & GNSS Antenna-CS7624A SKU8106

H-RTK F9P is the latest differential high-precision GNSS positioning system series from Holybro. This system provides multi-band RTK with fast convergence times and reliable performance, concurrent reception of GPS, GLONASS, Galileo and BeiDou, and fast update rate for highly dynamic and high volume applications with centimeter-accuracy. It uses a UBLOX F9P module, a IST8310 compass, and a tri-colored LED indicator. It also has a integrated safety switch for a simple and convenient operation.

PX4 Autopilot users:

The GPS RGB LED Driver Chip has been updated. Ensure the PX4 firmware is Stable Release v1.12.2 or newer for proper LED driver Support.

Ardupilot User:

Specification:

Pin Map:

Note: GPS2 port on both Pixhawk & Cube does not support Safety Switch function. You can use an external safety switch or disable the safety switch on ground control station application.

Note: GPS2 port on both Pixhawk & Cube does not support Safety Switch function. You can use an external safety switch or disable the safety switch on ground control station application.

We have designed three models of H-RTK F9P for you to choose, each with different antenna design to meet different customer needs.

H-RTK F9P Rover lite (SKU12017) & H-RTK F9P Rover lite 2nd GPS (SKU12025)

This model is lower cost, light weight, and has high performance, It can meet the needs of general DIY users. Due to the lower cost, this model can also greatly minimize the cost of large swarm drone projects such as swarm light shows. It has a integrated safety switch and a tri-colored LED indicator, and it is compatible with the open source Pixhawk series flight controller.
Package Included:

- H-RTK F9P Rover Lite *1 (Optional )
- H-RTK F9P Rover Lite 2nd GPS *1(Optional)
- Fixed Carbon Fiber GPS mount(40mm) *1
- GPS UART to USB Converter *1(For SKU12017)
- USB (type-c)cable *1
 

H-RTK F9P Helical (SKU12018)

This model uses a helical antenna, which has better performance than the lite version. This model can be used both on rover (aircraft) or as base station. The aluminum alloy shell design also has a integrated safety switch and a tri-colored LED indicator, and it is compatible with the open source Pixhawk series flight controller.

Package Included:

- H-RTK F9P *1
- High Precision GNSS Antenna(CH7604A) *1
- Fixed Carbon Fiber GPS mount(29mm) *1
- GH 10P cable 150mm *1
- GH 10P cable 400mm *1
- GH 10P to 6P cable 300mm *1
- USB type-c cable *1

H-RTK F9P Base (SKU12022)

The board is the same as number 2 above, but it is equipped with a high-gain antenna. This model is best suited to use as base station. The search speed and positioning accuracy are the highest among the three models.

Package Included:

- H-RTK F9P *1
- High Precision GNSS Antenna(CSX627A) *1  
(Note: The CS7624A antenna on the H-RTK F9P Base (SKU12022) & M8P Base (SKU12021) has been replaced with similar CSX627A until further notice. It will change back to CS7624A once supply stablized. The specific antenna model is subject to changes)
- Male-male SMA-TNC cable(length: 5m) *1
- 1/4'' Female to 5/8'' -11 Male Adapter *1
- USB type-c cable *1
*Tripod mount not included (sold separately) 
 

Download:

H-RTK_F9P_GNSS_Spec
H-RTK M8P&F9P GNSS Manual