CONECTOR BALANCEADOR DE CARGA 3 CELDAS x 2 A 6 CELDAS(MACHO 6S Y HEMBRA 3S X 2)

Products:

 

【Product specification】 can be washed with common strings (such as the IMAX B8) or separate red (such as UN A6) 
Charger for 6 groups of the same type, number of sessions the same 2-6S battery pack in parallel balance charge. To support 
Group 6 2S, or six groups 3S, or six groups 4S, or six groups 5S, 6S or 6 groups parallel balance charge. 
[Detail] 
1 balanced output line using 20AWG multi-strand silicone wire. 
2. Main output line adopt 14AWG multi shares high quality silicone line. 
3 T with security insert silicone cap. 
4 high-quality AMASS output plug. 
5 thick copper PCB to allow safe passage 30A of charging current.

Product Description

UN-A6 PLUS LiPo Battery Balance Charger(2-6S)

UN-A6 PLUS lipo battery balance charger combined advantages of UN-A6 and UN-A6PRO, optimizing the shortages, adopting NEW case and PCB wiring, offering bigger and clearer LCD display. This is the brand new UN-A6 PLUS!

UN-A6 PLUS adopts internationally accepted high efficiency "voltage-division charging" working mode. Voltage can be precision-controlled in plus or minus 0.002V, and current can be precision-controlled in 0.1A. The voltage deviation is less than 5mV after charging. This balance charger could be used to charge lipo battery, li-ion battery and A123 li-fe battery. Charging-finished voltage can be preset as well as charging current. At most 6 lipo packs could be charged simultaneously. It also comes with discharging function.

Features:
1). Input voltage could be displayed in this battery charger.
2). Dynamic balance function is added to adjust the charging current to shorten charging time according to cell voltage.
3). Two this UN-A6 chargers could be combined to compose one 12S charger and even share one input power.
4). Voltage precision: +/- 2mV, current precision: 0.1A. Just charging finished voltage deviation is less than 5mV.
5). Can division-charge 2-6S lipo battery packs.
6). Can simutaneously charge 3x2S, 2x3S, 1x6S battery packs.
7). Provide a full protection to the electric circuit, including nput overvoltage protection, over-heat temperature, input anti-connection protection,output anti-connection protection and output damage protection.
8). Fully automatic temperature control of radiating design.When the internal of the charger is not over heat, the radiator fan will not be activated, which has proven the quiet charging environment.
9). 6 charging circuit works separately, no interactively interference.
10).When CPU detects voltage in a channel has reached the default value, the charging circuit of this channel will be locked and stop working, so you do not have to worry about the batteries will be over charged. 
11). Maximum 8A charging current (0.3A-8A adjustable)
12). Input reqirment: DC 12V-14V/>12A
13). Five working modes make it be more stong in charging.

This charger does not incude switch power and needs to be purchased separately.

How to choose a proper switch power?
The input current of A6 is flexible. It can be selected by based on the consumer's maximum charge current. It can be calculated by using the following formula: for example, the input voltage is 12V, maximum charge current is 3A, to charge the 6S batteries, then the input current is calculated like: maximum output power is 3A*4.2V*6/0.85/12V=7.41A. Considering that the power supply should not be running in a full load, then increase 10% of input current for more flexible. So the input power is 12V/8A. 
One more example: 
Input voltage is 12A, maximum charge current is 2A, to charge the 3S batteries, input current is calculated like: maximum output power is 2A*4.2V*3/0.85/12V=2.47A*1.10=2.72A. So, 12V/3A is best suitable input power.

Industrial power supply Specification：

Switching power supply
Brand new high quality Switching power supply.

Description:
• 12V 20A Single Output Switching Power Supply
• The Single Switching Power Supply has wide input voltage range, steady and precise output voltage.
• Full load burn-in test.
• Over current, over voltage, short circuit protection.
• Low output ripple and noise.

Specification of the Power Supply:
• Input voltage: AC110V-240V
• Input frequency: 47-63hZ
• Input surge: cold, 20A@120VAC 20A@230VAC
• Output voltage: 12V
• Output current: 20A
• Output voltage adjustment range: ±10%
• Size: 20 x 11 x 5cm (L*W*D)
• Color: as photo shown
• Weight: 757g

2 Pin JST plug with 6 x Pico plug charging harness.
Charge up to 6 mini cells at once.
Great for Parkzone Eflite bind-n-fly aircraft batteries!

Micro JST Parallel Charge Lead (6 plugs)

This charge lead allows you to charge up to 6 x 3.7V micro JST batteries at once in parallel configuration.

Fits E-flite, Kyosho and other micro JST 3.7V batteries.
 

This handy little accessory will allow you to easily charge up to 6 x E-flite UMX Series 2S lipoly batteries at the same time in parallel. It features the JST-PH (E-flite style) micro connectors on one end x 6, and banana plugs w/JST-XH on the other side. This allows you to charge and balance up to 6 x 2S batteries at the same time with your standard charger.

JST-XH Parallel Balance Lead 4S 250mm (5xJST-XH)

2 Pin JST to 6 x E-Flight Ultra Micro plug Charging Harness

Gens ace 25/50C 1250mAh 3S1P 11.1V Airsoft Gun Lipo Battery with T Plug is designed specifically to power airsoft gun. Suitable for buffer tubes and AEG's where battery space is limited without sacrificing power and fits for LE stock like M4 etc .

Specification:

- Capacity: 1250mAh
- Voltage: 11.1V
- Discharge Rate: 25/50C
- Connector: T plug
- Dimensions: 124*19*16mm
- Net Weight: 91g
-Battery Cell Type: Lithium Polymer

Application:

Gens ace 25/50C 1250mAh 3S1P 11.1V Airsoft Gun Lipo Battery with T Plug Suitable for buffer tubes and AEG's where battery space is limited without sacrificing power and fits for LE stock like M4 etc.