A power distribution board from Matek Systems with integrated 5V and 12V voltage regulators and XT60 connector pad for tidy installations. This PDB is designed for 3s-4s Li-Po operation and has 6 pairs of ESC solder pads. The 5V onboard regulator supports currents up to 2A and the 12V supports up to 0.5A (bursts up to 0.8A). The ESC outputs support a maximum current of 25A each or 15A each if all six pads are used. Short bursts up to 30A and 20A respectively can be tolerated.

Please note the 12V BEC is primarily designed for operation with 4s batteries, if 3s is used, the BEC will output the LiPo voltage minus 1V.

Physical specification: -

• Dimensions: 36×50x4mm (without XT60)
• 30.5×30.5 mounting pattern (⌀3)
• Weighs just 11g with XT60 connector

Matek XT60 power distribution board features: -

• 9-18V DC input (3-4s Li-Po)
• LED power indicators
• 6 ESC outputs and a pair of +/- pads
•  

Matek LED Tail light WS2512B with Loud Buzzer Dual Modes for FPV Racer Multicopters












It comes as H Type tail light with 8xWS2812B LEDs & Loud Buzzer. It provides dual control modes, can be controlled by Flight Controller firmware (Cleanflight, Betaflight,etc.) or Transmiter.

Specification:
Brand name: Matek
Item name: LED Tail light with Buzzer board
Dual modes: FC control & TX control
TX mode: LED 7 colors (White, Red, Green, Blue, Yellow, Magenta, Cyan) LED 5 status (Constant light, Slow blink, Fast blink, Voilent blink)
Buzzer: Lost Plane Finder
FC mode: support Naze32, SPRacingF3, etc. with CleanFlight or Betaflight firmware
 Input voltage range: 4.5~5.2V DC
Power of TX mode (5V IN ): 1W/0.2A~2W/0.4A Size & mounting: Pls check the Layout
Weight: 5g

Package Included:
1 X LED Tail light with Buzzer board
 

This is the 5V loud buzzer from Matek. But what makes it loud I hear you cry?! Well this buzzer has a built-in MCU which makes it louder than your traditional 5V active buzzers. 

Specifications:

• Built-in MCU
• Working voltage range: 4.5-5.2V
• Power: 1W max
• Sound output: 90dB max
• Dimensions: 18x13x8mm
• Weight: 2g

Directions for use:

Resources:

For more information, check out the Matek DBuz5V Lost Model Beeper & FC 5V Buzzer manual. 

atek 5.8G 40CH 25/200/500mW Transmisor de Vídeo Conmutable VTX-HV con 5V/1A Salida BEC 
 

Specifications

• Input Voltage: 4.8~5.2V DC
• Working current: 20mA
• Sig pad: 0.5~4.5V output
• 1/2 pad has voltage divider built-in, 0.25~2.25V output.
• Pressure range: -2 to 2 kPa (-0.3 to 0.3 psi)
• Speed range: -200 to 200 km/h

*** use Target variant MATEKF411_RSSI for F411-WING,  Analog RSSI input is on ST1 pad. softserial_tx1 will be available on the LED pad.

Matek RGB LED Board 5050 12V For FPV RC Quadcopter Multicopter




 

Matek F722-PX Flight Controller for Airplanes and Multirotors, with a micro STM32F722RET6 MCU, and frequency up to 216Mhz, The flight controller firmware is iNavFlight / Betaflight.

Compatible with DJI FPV digital system.

Features:

• MCU: 216MHz STM32F722RET6

• IMU MPU6000

• BMP280 Barometer

• PIXEL OSD Uart

• 10 PWM / DSHOT outputs

• Built-in Black Box

• 6 Uarts & 1x Serial ports

• Compatible with WS2812 programmable LED strips

• Buzzer

• RSSI

• SBUS

MATEK H743-WING V3 ArduPilot INAV 3-8S H743 controlador de vuelo FC 30.5X30.5mm para Avión RC Multirotor Drones de ala fija

Nota: Esto se ha actualizado F743-Wing versión V3.

Se reemplaza H743-WING V2

Especificaciones FC

• MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash

• IMU: MPU6000 (SPI1) e ICM42605 (SPI4)

• Baro: Infineon DPS310 (I2C2)

• OSD: AT7456E (SPI2)

• Blackbox: ranura para tarjeta MicroSD (SDIO)

• 7x Uarts (1,2,3,4,6,7,8) con inversión integrada.

• 13x salidas PWM (incluyendo la almohadilla "LED")

• 2x I2C

• 1x lata

• 6x ADC (VBAT, corriente, RSSI, AirSpeed analógico, VB2, CU2)

• 3 LEDs para el Estado FC (azul, rojo) e indicador de 3,3 V (rojo).

• 1 ruptura SPI3

• Extensor USB/pitido con tipo C(USB2.0)

•  

• Interruptor de entradas de cámara Dual

• Interruptor de alimentación 5V/9V(12V) para cámara/VTX

• Sentido de corriente de alta precisión (90A continuo, 220A pico)

• Sensor de voltaje de la batería: 1K:10K (escala 1100 en INAV, BATT_VOLT_MULT 11,0 en ArduPilot)

• Divisor de voltaje ADC VB2: 1K:20K

• Divisor de voltaje ADC AirSpeed: 20K:20K

• Potencia estática 160mA @ 5V

Firmware FC

• ArduPilot(ChiBiOS): MATEKH743

• INAV: MATEKH743

Cámara PDB

• Rango de voltaje de entrada: 8 ~ 36V (LiPo 3 ~ 8S) con protección TVS.

• 2x almohadillas de alimentación ESC

• Senor actual: 220A, 3,3 V ADC (escala 150 en INAV, 66,7 a/v en ArduPilot)

• Resistencia de sentido: 90A continuo, 220A pico.

Salida BEC 5V

• Diseñado para controlador de vuelo, receptor, OSD, cámara, zumbador, 2812 LED_Strip, zumbador, módulo GPS, AirSpeed

• Salida 5,15 +/-0,1 V DC

• Corriente Continua 2 amperios, 3A pico

Salida BEC 9V /12V

• Diseñado para transmisor de vídeo, cámara, cardán, etc.

• Corriente Continua 2 amperios, 3A pico

• Opción de 12V con almohadilla de puente

Salida BEC Vx

• Diseñado para Servos

• Voltaje ajustable, 5V por defecto, 6V o 7,2 V a través de puente

• Corriente Continua 8 amperios, pico 10A

Salida BEC 3,3 V

• Regulador lineal

• Corriente Continua: Ma

Monitor físico

• Montaje: 30,5x30,5mm, Φ 4mm con arandelas Φ 3mm

• Dimensiones: 54x36x13mm

• Peso: 30g con extensor USB

Incluyendo

• 1 H743-WING V3

• 1x USB (tipo C)/bip (zumbador pasivo) extensor

• 1x cable de JST-SH-6P a JST-SH-6P de 20cm para el extensor USB.

• Cable de JST-GH-4P a JST-GH-4P de 2x20cm para Puerto CAN & I2C

• 1 condensador Rubycon ZLH 35V 470uF

• Dupont 2,54 pines(La placa se envía sin soldadura)

MICRO BEC 6-60V TO 5V/9V/12V-ADJ