The Mateksys F405-CTR flight controller has all the features of the original F405-OSD but now with the addition of a BMP280 barometer. The high-speed 168MHz 32bit F405 processor with BetaFlight firmware, OSD and BMP280 barometer gives this flight controller the power to easily control your drone.

It also has a blackbox to help you fine tune or to help determine what went wrong with any mishap. The OSD provides detailed information on battery voltage and other information. Also included is a PDB with an onboard 5V 2A continuous BEC system with 184A current sensor. This flight controller board is lightweight (only 10g) and because it has standard 30.5 x 30.5mm mounting holes in can easily fit into any drone.

Features:
• 168MHz STM32F405RGT6
• 6-axis MPU6000 accelerometer/gyro (SPI)
• BetaFlight OSD with AT7456E chip
• BMP280 (12C) barometer
• 4 x 30A 6 layer PDB
• 5V 2A continuous BEC (3A burst)
• 184A current sensor
• MicroSD BlackBox (SD/SDHC)
• VCP and 5 x UARTs
• 6 PWM/DSHOT outputs
• 12CI and DAC
• BF/NAV MatekF405 Target

Specs:
Input Voltage: 6~30V DC
MCU: 168MHz STM32F405
IMU: MPU6000 accelerometer/gyro (SPI) (6-axis)
Barometer: BMP280 (12C)
OSD: BetaFlight OSD w/ AT7456E chip
Blackbox: MicroSD card slot (SD/SDHC)
VCP: UART1, UART2, UART3, UART4, UART5
SBUS: Built in inverter for SBUS input (UART2-RX)
PPM/UART Shared: UART2-RX
SoftSerial Support: On S5 & S6
Camera Control: On S6 or DAC (optional)
VTX: Smartaudio and Tramp VTX protocol supported
Lights: WS2812 LED strip
Current Sensor: 184A
BEC: 5V 2A continuous (3A burst)
Voltage meter Scale: 1:10
LDO 3.3V: Max.300mA for Spektrum RX
Beeper: Yes
RSSI: Yes
Status LED's: 3 x LED's for FC STATUS (Blue, Red & 3.3V Red indicator)
PWM: 6 x PWM/DShot outputs without conflict
UART's: 5
Connections: 1 x group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
                      4 x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
                      1 x pair 12CI pads
Button: 1 x side-press button for BOOT(DFU) mode
Dimensions: 36x46mm PCB with 30.5mm mounting holes
Weight: 10g

Includes:
1 x Mateksys FC F405-CTR
1 x Rubycon ZLH 35V/470uF (Low ESR)
6 x Silicone M4 to M3 grommets
1 x FR4 PCB plate 36 x 36 x 1mm

Requires:
1 x Micro SD card (Up to 4GB)

MCU: 168MHz STM32F405RGT6
IMU: 32K ICM20602 gyro/accelerometer (SPI)
Baro: BMP280 (I2C)
OSD: BetaFlight OSD w/ AT7456E chip
Blackbox: MicroSD card slot (SD/SDHC)
VCP, UART1, UART2, UART3, UART4, UART5
Built in inverter for SBUS input (UART2-RX)
PPM/UART Shared: UART2-RX
SoftSerial on TX2, S5 or S6 optional
Camera control on S6 or DAC optional
Smartaudio & Tramp VTX protocol supported
Battery Voltage Sensor: 1:10
Current Sensor: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
BEC 5V: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
LDO 3.3V: Max.300mA
I2C1 SDA & SCL: Yes
WS2812 Led Strip : Yes
Beeper : Yes
RSSI: Yes

Informacion del Fabricante

Matek F411 flight controller for FPV racing drones, STM32F411 MCU, Frequency up to 100Mhz, Flight controller firmware is working the F405 to the limit. With OSD Betaflight and possibility of expansion with the FCHUB-A board

Features:

• MCU: 100MHz STM32F411
• IMU MPU 6000
• OSD Betaflight
• Dshot Outputs
• 6 PWM outputs
• 5 Uarts ports
• Compatible with FrSky telemetry

* More info: MATEK WEBSITE

This all-in-one FC by Matek is loaded with an STM32411 MCU, built-in SPI receiver(Frsky_X), PDB, BetaFlight OSD, BEC, and a current sensor. So pretty much everything but an ESC!

To learn in detail about this new SPI receiver protocol visit Oscar Liang's page or this brief information taken from Matek.

What is SPI RX?

• RF module 2500-2431 connected to STM32F411 MCU which communicate via SPI
• RF module 2500-2431 bind with Frsky Transmitter only ( D16 of EU LBT firmware is not compatible now).
• SPI RX is supported in BetaFlight firmware 3.3
• SPI RX doesn’t occupy any UARTs
• Telemetry data & RSSI are sent by default with Frsky_X protocol. No need to enable TELEMETRY in configurator and set up an AUX channel for sending the RSSI data from the transmitter.
• Telemetry & RSSI work with D16/D8 of NonEU firmware, and D8 of EU firmware
• Lua script is supported, work with D16 of NonEU firmware

How to bind

• 1. Power FC via USB or LiPo normally, RX LED(Green) blinking slowly
• 2. Connect FC to the configurator, Choose “SPI RX support” & “Frsky_X” in Configuration Tab–Receiver mode (They are set by default after flashing)
• 3. Then
• CLI “frsky_bind” and press ENTER, the RX LED will come solid.
• or Press RX Bind button, RX LED will come solid also
• 4. Start Transmitter in bind mode, the RX LED will fash slowly – Bind complete.
• Frsky_X — Transmitter D16(CH1-8 9ms or CH1-16 18ms）
• Frsky_D — Transmitter D8(CH1-8)
• 5. After CLI “defaults” or reflashing, SPI RX should be bound again.

Specifications

Flight Controller

• Target: MATEKF411RX
• MCU: 100MHz STM32F411CEU6
• IMU: MPU6000 gyro/accelerometer (SPI)
• OSD: BetaFlight OSD w/ AT7456E chip
• SPI RX: module 2500-2431, Frsky_X or Frsky_D protocol
• VCP, UART1, UART2
• WS2812 Led Strip: Yes
• Beeper: Yes
• PPM: RX2 pad
• Blackbox: No
• SBUS input: No
• I2C1 SDA & SCL: No

PDB

• Input: 6~30V (3~6S LiPo) w/TVS protection
• PDB: 4x30A (Max.4x46A)
• BEC: 5V 2A cont. (Max.3A)
• LDO 3.3V: Max.300mA
• Current Sensor 184A (Scale 179)
• Battery Voltage Sensor: 1:10 (Scale 110)

• 3x LEDs for FC STATUS (Blue) , RX (Green) and 3.3V indicator(Red)
• 4x PWM / DShot outputs
• 2x UARTs
• 1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
• 4x pairs of corner pads for ESC Power connections
• 1x Side-press button for BOOT(DFU) mode
• 1x Side-press button for RX bind
• 36x46mm PCB with 30.5mm mounting holes
• 10g

Includes

• 1x Matek 411-ONE Flight Controller
• 1x Rubycon ZLH 35V/470uF (Low ESR)
• 6x silicon grommets M4 to M3
• 2x IPEX- 2.4G antenna 15cm

MATEK LED x2 / 5V motor Mount para 1806 2204 2206 motor Multicopteros AZUL















 especificación
 nombre de marca: Matek
 nombre del artículo: montaje LED motor x2 / 5v
 adecuado para 1806 2204 2206 motor
 voltaje de entrada: 4 ~ 6v dc
 potencia: 0.6W @ 5v * 0.12a
 Tamaño: luz de la placa de diámetro: 28mm thinkness: 1.2mm
 peso: 1.5g
 18xx montaje del motor: paso de rosca m2. 11.5 ~ 16.5mm
 22xx montaje del motor: paso de rosca m3. 15.5 ~ 19.5mm


Paquete incluido:
 2 X LED X2 motor / 5v montar (Azul)
 1 X cable

MATEK LED x2 / 5V motor Mount para 1806 2204 2206 motor Multicopteros Verde















 especificación
 nombre de marca: Matek
 nombre del artículo: montaje LED motor x2 / 5v
 adecuado para 1806 2204 2206 motor
 voltaje de entrada: 4 ~ 6v dc
 potencia: 0.6W @ 5v * 0.12a
 Tamaño: luz de la placa de diámetro: 28mm thinkness: 1.2mm
 peso: 1.5g
 18xx montaje del motor: paso de rosca m2. 11.5 ~ 16.5mm
 22xx montaje del motor: paso de rosca m3. 15.5 ~ 19.5mm


Paquete incluido:
 2 X LED X2 motor / 5v montar (verde)
 1 X cable

MATEK LED x2 / 5V motor Mount para 1806 2204 2206 motor Multicopteros ROJO















 especificación
 nombre de marca: Matek
 nombre del artículo: montaje LED motor x2 / 5v
 adecuado para 1806 2204 2206 motor
 voltaje de entrada: 4 ~ 6v dc
 potencia: 0.6W @ 5v * 0.12a
 Tamaño: luz de la placa de diámetro: 28mm thinkness: 1.2mm
 peso: 1.5g
 18xx montaje del motor: paso de rosca m2. 11.5 ~ 16.5mm
 22xx montaje del motor: paso de rosca m3. 15.5 ~ 19.5mm


Paquete incluido:
 2 X LED X2 motor / 5v montar (rojo)
 1 X cable
 

MATEK LED x2 / 5V motor Mount para 1806 2204 2206 motor Multicopteros BLANCO















 especificación
 nombre de marca: Matek
 nombre del artículo: montaje LED motor x2 / 5v
 adecuado para 1806 2204 2206 motor
 voltaje de entrada: 4 ~ 6v dc
 potencia: 0.6W @ 5v * 0.12a
 Tamaño: luz de la placa de diámetro: 28mm thinkness: 1.2mm
 peso: 1.5g
 18xx montaje del motor: paso de rosca m2. 11.5 ~ 16.5mm
 22xx montaje del motor: paso de rosca m3. 15.5 ~ 19.5mm


Paquete incluido:
 2 X LED X2 motor / 5v montar (Blanco)
 1 X cable

• Matek RGB LED Board 5050 16V for FPV Multicopters and Planes
  
  Specifications:
  
  INPUT: 14~17V DC,4S Lipo battery
  Size: 47*10mm
  Weight: 2g
  Packing: LED BOARD 16V* 1, Cable 30cm*1
  Notes:
  Comes with a 0.3m long cable, users can cut it to a suitable length;
  Be ware of the positive and negative poles, as well as the insulation;
  Switch the related codes to ON, seven colors are selectable;
  The input is in a range of 14~17V. Can be powered by RX, but please make sure the output current of BEC is enough.
  Selectable Colors & Power:
  B ON =Blue, 0.4W, 25mA
  R ON =Red, 0.4W, 25mA
  G ON =Green, 0.4W, 25mA
  B+R =Megenta, 0.8W, 50mA
  B+G =Cyan, 0.8W, 50mA
  R+G =Yellow, 0.8W, 50mA
  B+R+G =White, 1.2W, 75mA

• RGB LED CIRCLE X6-12V
  
  Matek RGB LED CIRCLE X6/12V comes with six RGB5050 LEDs & one code switch. Seven colors are selectable by means of code switches. This LED board gives an eye-catching effect to your multirotors or planes when illuminated.
  
  Specifications:
  " INPUT: 10~13V DC? 3S LiPo?12VBEC
  " Size: Circle ?30mm (10mm /?3mm Mounting)
  " Select the colors with 3pin 1.25mm Code switch
  " Weight: 2.5g
  " Packing: LED CIRCLE X6/12V, 1pc, Cable 0.3m
  Notes:
  " Comes with a 0.3m long cable, users can cut it to a suitable length;
  " Be ware of the positive and negative poles, as well as the insulation;
  " Switch the related codes to ON, seven colors are selectable;
  " The input is in a range of 10~13V DC, can be powered by 3S Lipo or 12V BEC.
  Selectable Colors & Power @12v:
  " B ON =Blue, 0.6W, 0.05A
  " R ON =Red, 0.6W, 0.05A
  " G ON =Green, 0.6W, 0.05A
  " B+R =Megenta, 1.20W, 0.10A
  " B+G =Cyan, 1.20W, 0.10A
  " R+G =Yellow, 1.20W, 0.10A
  " B+R+G =White, 1.80W, 0.15A