Frsky Transmitter X9D Plus Parts Replacement LCD Screen

Description:

• Brand:Frsky
• Item Name: Frsky Transmitter X9D Plus Parts Replacement LCD Screen

Package Included:

• 1 x LCD Screen

X9E Gimbal. not for X9D

EVA case FRSKY

A top of the range 16 Channel X8R receiver from FrSky! (8 normal PWM outputs and all 16 channels on the dedicated S.BUS output) 

The X8R is in a Smaller package then previous 8 channel receivers, but has so much more capability. The new Smart Port supports the new hub-less sensors as well as the older hub analog sensors.

The X8R supports 8 standard servo outputs, and you can access all 16 channels by using the Sbus line with Sbus supported servos or use a FrSky S.BUS Decoder for the full 16 channels. Or you can use 2 X8R receivers in combination and the channels will sync 1-8 on the first and 9-16 on the second.

The X8 protocol is also backward compatible! In D8 mode it work with the DHT, DJT, DFT and DHT-U transmitter modules. In this mode you only have access to 8 channels but you still get to use the new Smart Port and digital sensors! And even cooler is the new antenna design “PCB” it reports up to a 20% gain in range over their older antennas. And the X8R is Firmware Upgradeable!

This is the perfect receiver for the FrSky Taranis, with its built in XJT Module or any of the D8 systems to take advantage of the new digital Smart Port sensors.

Specification:
Dimension: 46.5mm x 27mm x 14.4mm (1.83" x 1.06" x .56")
Weight: 16.8g (.59 oz)
Operating Voltage Range: 4V-10.0V
Operating Current: 100mA@5V 
Operating Range: >1.5km (Full Range)
RSSI output: analog voltage output (0~3.3V)

Compatibility:
All 16 channels require the FrSky Taranis, or the XJT module.
For 8 channels in D8 Mode you can use the FrSky Taranis or XJT, DJT, DFT, DHT and DHT-U modules

A top of the range 16 Channel X6R receiver from FrSky! (6 normal PWM outputs and all 16 channels on the dedicated S.BUS output)

Now supplied with the 2015 firmware to compy with EU regulations.

The X6R is no bigger than most other 6 channel receivers, but has so much more capability. The Smart Port supports the full range of hub-less sensors as well as the older hub analog sensors. 
The A2 port on the bottom allows you to connect an FBVS-01 battey voltage sensor for basic external voltage monitoring by pulling the jumper out if you prefer that to the integrated telemetry.

Six standard servo outputs are by the X6R and you can access all 16 channels by using the S.BUS line with S.BUS supported servos or use a FrSky S.BUS Decoder for the full 16 channels.

The X6R is also backward compatible! In D8 mode it works with the DHT, DJT, DFT and DHT-U transmitter modules. In this mode you only have access to 8 channels but you still get to use the new Smart Port and digital sensors!

This is the perfect receiver for the FrSky X9D Taranis, with its built in XJT Module or any of the D8 systems to take advantage of the new digital Smart Port sensors.

This is the 2015 version which complies with current EU regulations. Your Taranis X9D will need to have the latest firmware update.Alternatively, you can reverse update the X6R receiver.

Features:
• Solid RF link
• Inbuilt telemetry
• Up tp 16 channels supported by S.BUS
• Smart port enabled
• Upgradable firmware

Specs:
Dimension: 47mm x 24mm x 15mm 
Weight: 12.2g 
Operating Voltage Range: 4~10.0V
Operating Current: 100mA @ 5V
Operating Range: >1.5km (Full Range)
RSSI output: analog voltage output (0~3.3V) 

Compatibility:
All 16 channels requires the FrSky X9D Taranis, or the XJT module.
For 8 channels in D8 Mode you can use the FrSky X9D Taranis or XJT, DJT, DFT, DHT and DHT-U modules

FrSky Sensor Hub
 

El FrSky Sensor Hub se conecta en el puerto lateral digital (G, TX, RX) del receptor de telemetría  FRSKY con el cable suministrado.

Datos tecnicos:

Dimensiónes: 37 * 30 * 8 mm
Peso: 7 g (hub sensor sólo sin cables)
Rango de Voltaje: 4 ~ 10V
Rango de temperatura de funcionamiento: -20 ~ 80C
Característica: Firmware actualizable


Sensores opccionales:

Combustible: Sensor Indicador de combustible
GPS: GPS
Vario: Variometer Sensor
Volt: Lipo voltaje del sensor
Temp1 / 2: Sensor de temperatura
Alimentación: Fuente de alimentación
RPM: Sensor RPM
Acc: Sensor de aceleración triaxial
Datos: el uso previsto por cable para conectarse al puerto lateral digital (G, TX, RX) del receptor de telemetríaFrSky

MANUALES Y DESCARGAS

Introducción:
        FrSky sensor de voltaje de la batería se suministra como accesorio opcional Two Way Sistema de Telemetría.Hay tres rangos de voltaje a elegir: lipo 1S para la gama de voltaje de la batería 0V ~ 6.6V, hasta 3S Lipo 0 V ~13,2 V y hasta 5S lipo 0 V ~ 19.8V. Por favor, consulte la relación de división de voltaje de la batería para cadaopción:

Recommended Voltage Option               Max Lipo Pack Count            Battery Voltage Division Ratio
                                 1S                                                            1S                                                2:1

                                  2S                                                            3S                                                4:1

                                  3S                                                             5S                                                6:1

More detail：http://www.frsky-rc.com/download.asp

SOLO VALIDO PARA RECEPTORES S.PORT

1. Especificaciones:


      Modelo: FLVSS
       Dimensión: 45 * 21 * 7 mm
       Peso: 5,2 g
       Gama de la medida: 1S ~ 6S (La primera tensión lipo debe ser más que 3.55V)
       Móvil rango de visualización de voltaje: 0.20 ~ 4.20V
       Resolución de la pantalla Voltaje: 0.01V
       Precision del voltaje mostrado: 0.05V
       Rango de temperatura de funcionamiento: -30 ℃ ~ 70 ℃
       Pixel: 128 * 64 con pantalla OLED

2. Setup

2,1 sensor de voltaje Lipo FrSky se puede utilizar como un comprobador de tensión de lipo. Pantalla OLEDmuestra el voltaje y la célula tensiones totales, conectadas.

2.2 Dos sensores de voltaje Lipo FRSKY se pueden combinar para detectar lipos hasta de 12S.


 

2.3 Conectar "Data Out" de puerto de sensor de voltaje Lipo FrSky. Muestra el voltaje de los elementos de datos de pantalla-3 de FLD-02 y / o la tensión de visualización total DHT-U y lo conectan. (* ver nota más adelante)

 

* Nota:

     Cuando FLVSS funciona con hub sensor y FLD-02/DHT-U para mostrar tensión total y tensiones de los elementos que conectan, por favor, consulte a continuación los puntos:


1, Upgrade hub sensor Version2.0
  Driver para XP / Vista Win7: http://www.frsky-rc.com/download.asp?id=22

FSH-01 Upgrade ROM_V2.0: http://www.frsky-rc.com/download.asp?id=22

Sin to_sensor actualización cubo: http://www.frsky-rc.com/download.asp?id=22

2, Mejora DHT-U a Version2.0
  Driver para XP / Vista Win7: http://www.frsky-rc.com/download.asp?id=22

DHT-U Upgrade ROM_V2.0: http://www.frsky-rc.com/download.asp?id=23

Sin to_DHT-U actualización: http://www.frsky-rc.com/download.asp?id=23

3, FLD-02 actual muestra 6S como máximo. Si se requiere pantalla 12S, se requerirá nuevo firmware.